Hydraulic system
Drive shaft
Drive shaft for the common construction-machinery hydraulic pump series.

Quick answer
Drive shaft: what is it?
The drive shaft is the input shaft that carries torque from the engine into the rotary group, turning the cylinder block through a spline. It also has a seal journal where the shaft seal rides to keep oil inside the pump. When the spline wears with backlash or the seal journal grooves, the pump vibrates, whines and leaks oil at the shaft seal.
- Authorized JIC Hydraulics distributor
- Nationwide delivery · HCMC warehouse
- Wholesale and retail
- Fitment confirmed before we quote
The drive shaft carries the entire pulling load into the rotary group, so it is under constant twist and any slack shows up outside as vibration and noise. Its two typical failure zones are the spline that drives the cylinder block (or the input coupling) and the journal where the shaft seal rides. A worn spline gives backlash and a clunk; a grooved seal journal will leak oil even after a fresh seal is fitted.
Check the drive shaft in order
- Rock the input spline; sideways play means the spline is worn and peened
- Run a finger over the seal journal for grooves, ridges or sharp pits
- Look for a ring worn into the journal by the old seal lip
- Check the support bearings for end play and radial play
- Inspect the threads, snap-ring grooves and flange face for cracks or damage
A scored seal journal is a common reason a new seal still leaks — the shaft must be reconditioned or replaced. Việt Trung Hải stocks drive shafts and seals for K3V, A8VO and HPV, genuine parts, nationwide delivery.

Anatomy
Drive shaft inside the rotary group
The parts inside a piston pump work together to build flow and pressure. Tap any part to explore it and look it up.
Wear signs
When to replace the drive shaft
- Oil leak at the shaft seal
- Backlash or spline wear
- Vibration while the pump runs
- Grooving on the seal surface
Compatibility
Pump series we supply drive shaft for
| Pump / motor series | Maker | Products |
|---|---|---|
| K3V | Kawasaki | 15 products |
| A8VO | Uchida/Rexroth | 9 products |
| HPV | Komatsu | 8 products |
| M2X | Kawasaki | 3 products |
| MSF | Kayaba (KYB) | 3 products |
| K5V | Kawasaki | 2 products |
| PSV | Kayaba (KYB) | 2 products |
| A10V | Uchida/Rexroth | 1 product |
| DNB | Kawasaki | 1 product |
| K3SP | Kawasaki | 1 product |
Send the pump code or machine model and we'll confirm the exact fit before quoting.
Drive shaft products
View all 55 products
Kawasaki · DNBDrive shaft – Kawasaki DNB08DNB08On requestView · get a quote
Kawasaki · K3SPDrive shaft – Kawasaki K3SP36K3SP36On requestView · get a quote
Kawasaki · KVCDrive shaft – Kawasaki KVC925KVC925On requestView · get a quote
Kawasaki · M2XDrive shaft – Kawasaki M2X146M2X146On requestView · get a quote
Kawasaki · M2XDrive shaft – Kawasaki M2X150M2X150On requestView · get a quote
Kawasaki · M2XDrive shaft – Kawasaki M2X170M2X170On requestView · get a quote
Kawasaki · MXDrive shaft – Kawasaki MX173MX173On requestView · get a quote
Kawasaki · NVDrive shaft – Kawasaki NV270NV270On requestView · get a quoteMore Drive shaft codes (47)
- Drive shaft – Kawasaki NVK45DT
- Drive shaft – Kayaba MSF340
- Drive shaft – Kayaba MSF59P
- Drive shaft – Kayaba MSF89
- Drive shaft – Kayaba PSVD2-17
- Drive shaft – Kayaba PSVD2-21
- Drive shaft – Rexroth A10VD43
- Drive shaft – Rexroth A8V107
- Drive shaft – Rexroth A8V55
- Drive shaft – Rexroth A8V80
- Drive shaft – Rexroth A8V86
- Drive shaft – Rexroth A8VO107
- Drive shaft – Rexroth-Uchida A8VO160
- Drive shaft – Rexroth A8VO200
- Drive shaft – Uchida AP2D36
- Drive shaft – Kawasaki K3V180DT
- Rear drive shaft – Kawasaki K5V140DT
- Rear drive shaft – Kawasaki NV111DT
- Rear drive shaft – Kawasaki NV137DT
- Rear drive shaft – Komatsu HPV160
- Rear drive shaft – Komatsu HPV55
- Rear drive shaft – Komatsu HPV90
- Rear drive shaft – Komatsu HPV95
- Rear drive shaft – Rexroth-Uchida A8VO160
- Rear drive shaft 12T – Kawasaki K3V112DT
- Rear drive shaft 12T – Kawasaki K3V140DT
- Rear drive shaft 12T – Kawasaki K3V180DT
- Rear drive shaft 12T – Kawasaki K3V63DT
- Rear drive shaft 13T – Kawasaki K3V112DT
- Rear drive shaft 13T – Kawasaki K3V140DT
- Rear drive shaft 13T – Kawasaki K3V180DT
- Rear drive shaft 13T – Kawasaki K3V63DT
- Front drive shaft – Kawasaki K3V112DT
- Front drive shaft – Kawasaki K3V63DT
- Front drive shaft – Kawasaki K5V140DT
- Front drive shaft – Kawasaki NV111DT
- Front drive shaft – Kawasaki NV137DT
- Front drive shaft – Komatsu HPV160
- Front drive shaft – Komatsu HPV55
- Front drive shaft – Komatsu HPV90
- Front drive shaft – Komatsu HPV95
- Front drive shaft – Rexroth-Uchida A8VO160
- Front drive shaft 14T – Kawasaki K3V112DT
- Front drive shaft 14T – Kawasaki K3V140DT
- Front drive shaft 17T – Kawasaki K3V180DT
- Front drive shaft 17T – Kawasaki K3V180DTH
- Fixed shaft – Kawasaki KVC925
Find it
Order the exact part
Pick whichever suits you — our team confirms fitment, then quotes.
By part number
Send the number stamped on the old part for the exact match.
By machine model
e.g. Komatsu PC200-8, Hitachi ZX200 — send the model to match.
By pump / motor series
e.g. K3V112, A8VO107 — when you know the pump code.
FAQ
Frequently asked questions
Why does the drive shaft still leak after a new seal?
Usually because the journal where the seal rides has worn a groove, so the new lip can't seal against it. The journal must be reconditioned or the shaft replaced; swapping only the seal will leak again.
What are the signs of a worn drive-shaft spline?
The pump vibrates and knocks on load reversals or at start-up as the loose spline slaps against the block. In bad cases drive is lost intermittently, and it wears the cylinder-block spline quickly too.
What is the drive shaft's job in the rotary group?
The drive shaft takes power from the engine and passes it through the spline to spin the cylinder block, while riding on bearings and sealing oil at the shaft seal. It is the only path for torque into the rotating assembly.
What determines the correct drive shaft?
The pump code and input type: spline tooth count, length, seal-journal diameter and flange style all differ between families. Compare the old shaft and count the spline teeth before ordering.
Get a quote
Need the right part, fast?
Send your machine model and the part you need — we confirm fitment and quote.
- Pump code / plate
- Machine model
- Photo of the old part