Skip to main content

Heavy-equipment parts · Hydraulic pumps · Rotary groups · Machinery

Hồ Chí Minh(+8428) 3898 2851
Maintenance & uptime

Daily Excavator Checks: the 10-point checklist before you start work

A disassembled JIC hydraulic rotary group: cylinder block, pistons, shoe plate, valve plate, pump shafts and JIC boxes

Quick answer

A daily excavator check is the few minutes you spend before each shift walking around the machine: reading oil levels, hunting for leaks, glancing at the air filter, tracks, grease points and warning lights. This small habit catches faults while they are still cheap, instead of leaving the machine stranded on site. Following a fixed sequence means you never skip a point.

A daily excavator check is the few minutes you spend before each shift walking around the machine, reading oil levels, hunting for leaks, glancing at the air filter, tracks, grease and warning lights. This small habit keeps the machine running smoothly all day and helps you catch faults while they are still cheap. A dry pin, a puddle of oil under the belly, or a slightly swollen hose — spotted early, you fix it in the morning; ignored, it can become a full day parked on site. This article is a practical checklist, in the same order a working technician follows on site.

Why a daily excavator check is worth it

An excavator works in dust, vibration and heavy load all day. Parts rarely fail in a single second; they warn you first with small signs that only someone willing to look will see. When you check every morning, you build a habit of catching faults early, and early faults are always cheaper than late ones. That is why well-run fleets make their operators walk around before they start the engine.

Prepare before you inspect

Park on level ground, lower the bucket to the ground and switch off the engine before you open a cover or reach inside. Level ground lets you read oil levels correctly, because a tilted machine gives false numbers. Let the machine cool a little if it has just been running, since hot coolant and oil can scald. Keep clean rags, a torch and a grease gun ready so you are not running back and forth.

Walk around the machine before starting

Before you climb into the cab, walk a full loop around the machine and look with your eyes. Look for loose bolts, cracked panels, rubbing hoses, and anything hanging loose or fallen off. Look at the ground where the machine sat overnight: a wet patch there tells you where it is leaking. This walk takes only a minute but catches a lot.

Check the engine oil level

Pull the dipstick, wipe it clean, reinsert it and pull it out to read. The oil should sit within the upper marks; too little oil wears the engine fast, and too much is also harmful. Notice the colour and smell: thick black oil or a burnt smell is a sign to pay attention. If the level drops quickly between checks, the machine is burning or leaking oil somewhere, and you need to find it.

Check the hydraulic oil

Hydraulic oil is the blood of an excavator; almost every movement depends on it. Read the sight glass on the tank with the boom and bucket in the standard position the machine manual calls for. Good oil is usually clear and clean; milky oil means water has got in, while dark oil with a burnt smell points to overheating. A dropping hydraulic level usually goes with a leak, so if it looks low, trace the lines and cylinders to find the seep.

Coolant and radiator

Check the coolant level in the overflow bottle while the machine is cold; do not open the radiator cap when it is hot. Look through the radiator to see whether the fins are blocked with dust, debris or soil, because a dirty radiator makes the machine run hot. Gently feel the coolant hoses for any bulge or fine cracks. Overheating is one of the heaviest and most expensive failures, so do not take this step lightly.

Hunt for leaks under and around the machine

A leak is how the machine tells you it is hurting. Bend down and look under the belly, around the hydraulic pump, the hose fittings and the cylinders. Leaking hydraulic oil is usually shiny and collects dust into streaks; engine oil is darker; coolant has its own colour and smell. Note where it leaks and watch it: a slow drip can wait, but a pressurised spray means you stop the machine at once.

The air filter: why dust is the enemy

On Vietnamese job sites, dust is the quietest killer of engines. Open the air filter housing, take out the element and hold it against the light: if it is packed thick with dust, airflow into the engine is choked, the machine loses power and burns oil. Tap it gently to shake dust loose if the element is still good, but a torn or heavily clogged element must be replaced. In the same family as the air filter, do not forget the hydraulic filters, because a clogged filter makes the whole system work harder.

Check the tracks and undercarriage

Walk along both sides of the travel gear and look at the track. A track that is too loose slaps, throws and wears fast; one that is too tight loads the machine and harms the drive. Look for cracked links, bent shoes, seized rollers or oil weeping from an idler. Listen as it moves: an unusual grinding or knocking is the undercarriage asking to be looked at.

Grease the joints and pins

Pins and bushings take the most load and wear on the arm and bucket. Pump grease into the nipples at the points the manufacturer marks, until you see old grease pushed out. A dry pin squeals and wears very fast, leading to play and eventually a broken pin. A few minutes of greasing each day greatly extends pin and bushing life, and it is the cheapest thing you can do for the machine.

Check the bucket, teeth and pins

Look closely at the bucket teeth: worn stubby teeth make the machine dig hard, burn fuel and work slowly. Check that the tooth pins are still tight, because losing a tooth mid-dig is both a productivity and a safety problem. Look at the bucket pins and links for play, cracks or coning wear. If you need to replace teeth, pins or links, choose heavy-equipment parts from a clear source so they fit properly and last.

Warning lights and gauges

Turn the key to the on position and let the warning lights run their self-test, lighting up and then going out. Learn which light is oil, temperature, charge and filter blockage, so when one lights up while running you know its meaning at once. If a warning light does not go out after the engine starts, do not push on with work — find the cause. The dash is how the machine talks to you; ignoring it is ignoring an early warning.

Checks at start-up: listen and look

Start the engine and let it idle for a moment before you begin work. Listen to the engine: a knock, a whine or any strange noise is worth stopping to investigate. Look at the exhaust smoke — black, white or blue smoke that lingers all say something about combustion or oil. Feel the vibration: unusually strong shaking often signals a part that is loose or misaligned.

Check brakes, steering and controls

Before you move, gently test the control levers to be sure they respond and return to centre properly. Test the swing brake and travel brake at low speed in a safe area. A lever that has play, lags or jerks is a sign of wear or air in the system. Safe operation depends on the controls responding exactly as you expect.

Is there anything to check after the shift?

Yes, and many people forget this step. At the end of the shift, do a quick loop again to catch what came up during the day: a pin that just ran dry, a hose that just started to seep, or a track shoe that just bent. Wipe off thick mud, especially around the radiator and undercarriage, so tomorrow morning is easier to inspect. In the rainy season, cleaning down at day-end matters even more; see how to go about storing an excavator in the wet season to avoid rust and electrical faults.

Keep an inspection log

A small notebook in the cab is worth more than you think. Note the date, the machine hours, what you checked, and anything unusual you saw. The log helps you spot trends: an oil level creeping down, a leak growing day by day, or a noise getting louder. When you need to call a technician, this notebook helps them find the fault much faster.

The daily excavator check list

Here is a compact table to stick in the cab. This is the core of a daily excavator check, arranged in the order you should work through.

Step Check point Signs to watch
1 Walk around the machine Loose bolts, cracked panels, wet patch on the ground
2 Engine oil Low level, burnt smell, quick drop
3 Hydraulic oil Milky look, dark burnt smell, low level
4 Coolant Low level, radiator blocked with dust, bulging hose
5 Leaks Dust-caked oil streaks, pressurised spray
6 Air filter Thick dust, torn element
7 Tracks and undercarriage Loose, tight, cracked links, strange noise
8 Grease pins and bushings Dry pin, squealing
9 Bucket teeth and pins Worn teeth, loose pins
10 Warning lights A warning light that will not go out

Common failures from skipping checks

People tend to skip the check on busy days, and that is exactly when failures happen most. Running with a clogged air filter makes the engine weak and wears it fast. Working with low hydraulic oil makes the pump hot and can destroy it. Missing grease for a few days is enough for a pin to start playing and squealing. These faults are all cheap to prevent but expensive to repair.

When to call a technician or replace parts

Some signs you should not try to work through yourself. A pressurised oil spray, strange lingering smoke, a knock inside the engine, or a warning light that will not go out are all times to stop and call someone skilled. When replacing a part, weigh genuine against aftermarket by the machine condition and your budget; genuine fits more precisely, while good aftermarket still serves if you choose the right source. Parts prices vary by machine age, condition and supply, so compare before you decide.

Follow the manufacturer documentation

Every machine model has slightly different check points and grease-nipple locations. When unsure, follow your own machine manual; for example, the technical documentation from Kobelco describes the start-of-shift inspection sequence clearly for each model. Following the maker guidance keeps you from missing an important point or doing it wrong. Treat the checklist here as a general frame, and the machine manual as the final standard.

Daily checks only catch the problems in front of you; they do not replace scheduled maintenance. What you write in the log each day tells you when to change oil, change filters or adjust tracks. Put the two together and the machine lasts longer with fewer sudden stops. See the excavator maintenance schedule to know which interval calls for what, and plan ahead.

Start today

Pick a fixed sequence, stick the checklist in the cab, and complete it every morning until it becomes reflex. When you need filters, pins, bucket teeth or the right replacement parts, look at our heavy-equipment parts catalogue to choose a clear source and get fitment advice. A few minutes each day keeps your machine working hard.

Key takeaways

  • Walk around the machine before starting to catch faults by eye.
  • Read engine and hydraulic oil levels on level ground with the machine cool.
  • Hunt for leaks under the belly; a pressurised spray means stop at once.
  • Check the air filter daily because dust is the quiet killer of engines.
  • Grease pins and bushings every day to avoid play and broken pins.
  • Keep a log to spot failure trends and link it to scheduled maintenance.

Written by

Lê Minh Tuấn

Lê Minh Tuấn handles scheduled maintenance and machine longevity at Việt Trung Hải. He writes about oil, filters, service intervals and the habits that keep machines running reliably.

Related parts

The exact parts discussed above — send your machine model or pump code to match.

Frequently asked questions

How long does a daily excavator check take?

Usually just a few minutes if you follow a fixed sequence. Once it is a habit, the walk-around and reading the oil levels go very quickly. That time is far smaller than a session parked on site because of a failure.

Should I check before or after starting the engine?

Both. Most checks are done with the machine off and cool, such as oil levels and leaks. Then start it, idle it and listen, look at the smoke and feel the vibration to catch signs that only appear when it runs.

Which signs mean I must stop the machine at once?

A pressurised oil spray, a strange knock inside the engine, unusual lingering smoke and a warning light that will not go out are signs to stop immediately. Pushing on in these cases usually turns a small fault into a big one. Switch off and find the cause before continuing.

Why is the air filter so important on a dusty site?

Dust reaching the engine grinds the cylinders and slowly saps power. A clogged air filter chokes the airflow, so the engine burns poorly, uses oil and runs hotter. In a dusty setting, checking the air filter daily is one of the most worthwhile tasks.

Should I choose genuine or aftermarket when replacing parts?

It depends on the machine condition and your budget. Genuine parts fit more precisely and usually last longer, while good aftermarket still serves if you pick the right source. Prices vary by machine age and supply, so ask for advice to match the right part to your machine.

Related articles

Excavator friction discs, steel plates and slewing ring gearsMaintenance & uptime

Travel motor maintenance on excavators: 6 routine jobs

Six final-drive jobs for excavators: change the gear oil, read the drained oil (metal glitter, milky, burnt smell), check the face seal, listen for bearings, test the parking brake, and set track tension — plus where JIC parts and ZVL bearings fit in a rebuild.

Lê Minh Tuấn13 min

Need the right part for your machine?

Send the machine model, pump code or a spec-plate photo — we confirm fitment and quote.

Get a quote