
Pin – Komatsu HPV75
Quick answer
The Komatsu HPV75 rotary group is the rotating assembly that generates flow and pressure inside a Komatsu HPV-series main pump for mid-size excavators.
Việt Trung Hải supplies HPV75 groups in genuine Komatsu and JIC form — as JIC's authorized distributor — machined to the correct code and seating in the original housing, with a fast quote.
Not sure of the code? Send a photo of the pump nameplate or your machine model and our technicians will check it before you order.
- Part type
- Rotary group
- Brand / pump line
- Komatsu · HPV
- Model code
- HPV75
- Condition
- New, correct code
- Availability
- On request
Komatsu HPV75 rotary group — what it fits
The rotary group is the rotating assembly inside a piston pump — cylinder block, pistons, valve plate, swash plate and drive shaft — that generates the pump's flow and pressure. The HPV75 group fits the Komatsu HPV-series main pump on mid-size Komatsu excavators, and carries the pump's heaviest load, so every mating face must be precise.
Signs it needs replacing
Weak hydraulics, slow lift and lost power on combined movements signal a worn rotary group. Fast-heating oil, pump whine, and copper or metal particles in the oil point to scored pistons, valve plate or swash plate. Once the faces wear, the pump can no longer hold pressure.
Choosing quality parts
Those faces need the right material, hardness and machined flatness to seal and last. Việt Trung Hải is an authorized JIC Hydraulics distributor: the JIC HPV75 rotary group is JIC's own part, ground to the same code and fitting tolerance, so the block seats evenly on the valve plate from the first build. Genuine Komatsu sets are stocked as well. Send the HPV75 pump code for a fast quote.
Frequently asked questions
Which excavators does the Komatsu HPV75 rotary group fit?
The HPV75 is the rotary group for a Komatsu HPV-series main pump used on mid-size excavators. Send us your machine serial or pump code and Việt Trung Hải will confirm the exact rotary group for your model.
When should I replace the rotary group instead of the whole pump?
When the machine loses power, the oil overheats and you see copper particles, the rotary group is usually worn. Replacing the correct-code group restores flow and pressure without a full pump swap. Have a technician inspect the valve plate and cylinder block first.
The machine is still weak after a new HPV75 rotary group — where do I look?
Start with the oil and filters, then the flow regulator, relief valve and servo piston: a new group only builds pressure if the control side is sound. Check the housing and drive shaft too — a worn shaft loads the rotating stack unevenly even when the JIC group is the right code and fits tight.
Get a quote
Request a quote: Pin – Komatsu HPV75
This is a quote model, not a cart. Send your machine model or pump code and we confirm fitment and quote fast.
Related parts
Komatsu · HPVRotary group kit – Komatsu HPV75HPV75On requestView · get a quote
Komatsu · HPVSwash plate – Komatsu HPV75HPV75On requestView · get a quote
Komatsu · HPVShoe plate – Komatsu HPV75HPV75On requestView · get a quote
Komatsu · HPVRetainer plate – Komatsu HPV75HPV75On requestView · get a quote
Komatsu · HPVValve plate – Komatsu HPV75HPV75On requestView · get a quote
Komatsu · HPVPiston – Komatsu HPV75HPV75On requestView · get a quote
Komatsu · HPVBall guide – Komatsu HPV75HPV75On requestView · get a quote
Komatsu · HPVCylinder block – Komatsu HPV75HPV75On requestView · get a quoteTechnical handbook