
Cylinder block – Komatsu HPV90
Quick answer
The Komatsu HPV90 cylinder block is the barrel holding the piston bores that rotate around the drive shaft, used in the HPV main pump on roughly 20-tonne excavators like the Komatsu PC200.
Việt Trung Hải keeps it as a genuine part and as a JIC part, each to the correct code and ready for the original housing, with a fast quote.
Not sure of the code? Send a photo of the pump nameplate or your machine model and our technicians will check it before you order.
- Part type
- Cylinder block
- Brand / pump line
- Komatsu · HPV
- Model code
- HPV90
- Condition
- New, correct code
- Availability
- On request
What the HPV90 cylinder block does
The cylinder block is the barrel holding the piston bores that rotate around the drive shaft; the pistons reciprocate to draw and push oil. The HPV90 code belongs to Komatsu's HPV main-pump family, fitted on roughly 20-tonne excavators such as the Komatsu PC200. It is a heavy-loaded rotating part working against the valve plate and piston shoes.
When to replace
Watch for weak pump output, slow boom under load, unusual whine or knock from the pump, and internal leakage. Scoring, pitting or uneven wear on the block face and tapered bores raise clearances and drop the efficiency of the whole pump.
Choosing quality parts
Việt Trung Hải, an authorized JIC Hydraulics distributor, keeps the HPV90 block on the shelf as a genuine part and as a JIC part. The JIC block comes from JIC itself, cut to the HPV90 code and to interchange tolerance — correct material, hardness and surface finish keep the seal tight under load, and it lands in the original housing with nothing to adjust. Contact us for the right code and a fast quote.
Frequently asked questions
Which excavator does the HPV90 cylinder block fit?
The HPV90 code belongs to Komatsu's HPV main pump, typically on ~20-tonne excavators such as the Komatsu PC200. Send us your machine year and pump number and we will confirm the exact code before quoting.
When should the cylinder block be replaced?
When the pump goes weak, the boom is slow, you hear knocking, or the oil runs unusually hot. If the block face is scored or pitted and the bores are tapered, replace it to avoid internal leakage and further pump damage.
The PC200 goes weak once the oil is hot — is the block to blame?
Usually yes, when the block face and valve plate are worn: hot oil thins out, internal leakage climbs and the pump cannot hold pressure. Measure case drain flow and look at the block face before you decide. If that is it, an HPV90 block to code brings the power back — Việt Trung Hải has the genuine part and the JIC part.
Get a quote
Request a quote: Cylinder block – Komatsu HPV90
This is a quote model, not a cart. Send your machine model or pump code and we confirm fitment and quote fast.
Related parts
Komatsu · HPVRotary group kit – Komatsu HPV90HPV90On requestView · get a quote
Komatsu · HPVRear drive shaft – Komatsu HPV90HPV90On requestView · get a quote
Komatsu · HPVFront drive shaft – Komatsu HPV90HPV90On requestView · get a quote
Komatsu · HPVSwash plate – Komatsu HPV90HPV90On requestView · get a quote
Komatsu · HPVShoe plate – Komatsu HPV90 (rear)HPV90On requestView · get a quote
Komatsu · HPVShoe plate – Komatsu HPV90 (front)HPV90On requestView · get a quote
Komatsu · HPVRetainer plate – Komatsu HPV90HPV90On requestView · get a quote
Komatsu · HPVValve plate – Komatsu HPV90HPV90On requestView · get a quoteTechnical handbook